Reconstitution calculator

Work out the concentration of a reconstituted vial or a prefilled pen, the volume that carries a given mass, and how many withdrawals or deliveries you get from it. For laboratory planning only.

What you are preparing

Compound

Optional example; check the mass on your vial

Peptide in the vial

mg

Diluent added

ml of bacteriostatic water

Mass to withdraw

Per withdrawal

Syringe size

Barrel capacity

Results

10 mg/ml30 mg made up in 3 ml

Volume to withdraw
0.2 ml200 µl, for 2 mg
Withdrawals per vial
15 × 2 mg
Concentration per 0.1 ml
1 mg
Molar concentration
—Choose a compound to calculate this
0.2 ml fills 20% of a 1 ml syringe.

Figures assume the full contents of the vial dissolve in the volume added and that the peptide itself contributes negligible volume. Molar concentration is calculated from the unmodified linear sequence, so it will be slightly off for compounds carrying a terminal amide, an acetyl group, a fatty-acid chain or a metal.

Concentration 10 mg/ml. Withdraw 0.2 ml for 2 mg. 15 withdrawals per vial.

What you need

Prepare the work area and all materials before opening either vial.

Bacteriostatic water

The usual diluent for multi-use research vials. It contains 0.9% benzyl alcohol. Use a fresh, in-date vial and never reuse one that has become cloudy.

Sterile syringes and needles

Use a fresh sterile syringe and needle for every transfer. A larger needle makes drawing water easier; a fine needle gives more control when adding it to the peptide vial.

Alcohol swabs

One for each stopper, every time it is accessed. Allow the alcohol to dry before piercing the stopper.

Acetic acid 0.6%

Only for peptides whose product page specifically calls for it, such as GHK-Cu. Do not substitute household vinegar.

Refrigeration

Have 2–8°C storage ready before starting. Return the vial to the fridge as soon as reconstitution is complete.

A clean work area

Clear the surface, wash your hands and keep the vial stoppers and needle tips away from anything non-sterile.

Reconstitution, step by step

  1. Let both vials reach room temperature

    Take the peptide and diluent out of the fridge and leave them upright for 15–20 minutes. Adding cold diluent to cold powder can slow dissolution.

  2. Decide on the concentration first

    Use the calculator above to choose a diluent volume that gives practical withdrawals. Write the planned volume down before you uncap anything.

  3. Wipe both stoppers

    Swab the bacteriostatic-water stopper and the peptide-vial stopper separately. Let them air-dry.

  4. Draw the diluent

    Pull into the syringe the exact volume you chose in the calculator. Check the barrel at eye level.

  5. Add it down the vial wall

    Pierce the peptide-vial stopper and angle the needle so the diluent runs slowly down the glass. Avoid spraying the lyophilised cake directly.

  6. Swirl, do not shake

    Roll the vial gently between your fingers, then swirl it in small circles. Most peptides dissolve within a few minutes. Vigorous shaking can damage fragile sequences.

  7. Inspect the solution

    It should be clear and free of visible particles unless the product page says otherwise. Do not use a solution that remains cloudy, discoloured or particulate.

  8. Label and follow the storage documentation

    Write the concentration and date on the vial. Follow the storage conditions and stability information supplied for the specific product, formulation and lot.

Common mistakes

Shaking the vial

Foam and shear forces can unfold or aggregate peptides. Gentle swirling is enough.

Spraying onto the powder

A high-pressure jet can damage the lyophilised cake. Let the diluent run down the glass.

Reconstituting straight from the fridge

Temperature shock slows dissolution and can cause condensation. Let both vials warm first.

Guessing the concentration later

The label tells you mass, not concentration. Record the volume you added as soon as you add it.

Swabbing only the first time

The stopper is no longer sterile once handled. Swab before every withdrawal.

Repeated freeze–thaw cycles

Each cycle stresses the peptide. If freezing is permitted, divide into single-use aliquots first.

Concentration reference

Compare the listed peptide masses and diluent volumes in mg/ml. The table uses the same calculation as the tool above.

Concentration reference in mg/ml
Vial mass1 ml1.5 ml2 ml3 ml5 ml
5 mg53.32.51.71
10 mg106.753.32
15 mg15107.553
20 mg2013.3106.74
30 mg302015106
50 mg5033.32516.710
100 mg10066.75033.320

A more concentrated solution means a smaller volume to withdraw, which makes small masses harder to measure accurately. If a withdrawal works out below about 0.05 ml, reconstitute in a larger volume instead.

Questions

How long does a reconstituted vial last?

Follow the storage conditions and stability information in the documentation for the specific product, formulation and lot. If that information is missing, contact Aminos before preparing or storing the material. This calculator does not establish a storage temperature or shelf life.

Bacteriostatic water slows bacterial growth; it does not make a peptide indefinitely stable.

Do I have to use bacteriostatic water?

For most multi-use research vials it is the practical choice. Sterile water has no preservative and is better suited to a single-use preparation. Some sequences call for a weak acetic-acid solution; follow the product page rather than improvising.

What if the powder will not dissolve?

Give it time at room temperature and swirl gently. Do not shake or heat it. Check the product page for a sequence-specific solvent note. If the solution remains cloudy or particulate, set it aside rather than forcing it.

Can I freeze the solution?

Only when the product page says the sequence tolerates freezing. Aliquot first so each portion is thawed once. Never repeatedly freeze and thaw the same vial.

Should I reconstitute the whole vial at once?

Usually yes, because opening or dividing dry material outside controlled conditions increases contamination and weighing error. If your protocol requires aliquoting dry material, use suitable laboratory equipment and a validated procedure.

Why does my vial look like it contains nothing?

Small peptide masses form a thin, sometimes transparent lyophilised film on the glass. The labelled mass may be present even when there is no obvious cake. Do not assume an apparently empty vial is empty.

Is the mass on the label the mass of peptide?

The label gives the nominal peptide content. Counter-ions, residual water and excipients may also be present. For molar work, use the certificate of analysis and the correct molecular form.

How do I work out a prefilled pen?

Switch the calculator to Prefilled pen. Enter the total peptide mass, total solution volume and mass per delivery. The result shows concentration, volume per delivery and the number of whole deliveries in the cartridge.

Does the powder add to the volume?

At the masses used in these vials the peptide contribution is normally negligible for routine planning, so the calculator treats the final volume as the volume of diluent added. High-precision analytical work should measure the actual final volume.

Read the compound references or open the peptide sequence tool. Laboratory reference only. This calculator performs concentration arithmetic for planning laboratory work. It is not a dosing tool, and nothing on this page is medical or veterinary guidance. Aminos compounds are sold strictly for in-vitro laboratory research use, are not medicines, and are not for human or animal use.